 |
|
 |
|
 |
|
 |
|
 |
|
 |
|
 |
|
 |
|
 |
|
KENT MODEL 3VS
VERTICAL MILLING MACHINE $7,950.00
- 3 HP spindle motor, variable speed head, 3VSF model with AC-Frequency drive, digital RPM display, and load meter
- 9” x 42” hardened and ground table (Optional 9” x 49” style available)
- Table, saddle, and knee with hardened and ground dovetail ways
- Precision ground leadscrews with backlash compensating double nut
- Precision bored and ground milling head, with super precision ABEC-7 bearings
- Meehanite® casting, with built in coolant reservoir in machine base
- Centralized one-shot lubrication, with metered check-valves
OPTIONAL ACCESSORIES:
| Acu-Rite 200S DRO System (2-axis, 0.0002” res. 9”x49”) | $ 1,850.00 |
| DRO installation charge | $ 150.00 |
| Table (x-axis) power feed | $ 450.00 |
| Saddle (y-axis) power feed | $ 600.00 |
| Knee (z-axis) power feed | $ 600.00 |
| Air power drawbar (Maxi-Torque, made in USA) | $ 800.00 |
| Flood coolant system (built-in base) | $ 550.00 |
| Chip tray | $ 450.00 |
| Right angle milling attachment with arbor support | $ 850.00 |
| Riser block (4”) | $ 550.00 |
| Riser block (8”) | $ 650.00 |
| Angle-lock vise (6”) | $ 400.00 |
| Upgrade to 440V power on 3VSF AC-Freq drive model | $ 200.00 |
SPECIAL MILL PACKAGE PROMOTION:
KTM-3VS with Acu-Rite 200S DRO (2-axis) and table power feed (Installed)............$ 9,950.00
KTM-3VSF with Acu-Rite 200S DRO (2-axis) and table power feed (Installed)..........$ 11,650.00
Special Accessories Package: 6” vise, R-8 collet set, and clamping kit..................... $ 450.00
MACHINE SPECIFICATIONS:
Table size |
9” x 49” (Opt. 9” x 49”) |
Table travel (X-axis) |
35” |
Saddle travel (Y-axis) |
12” |
Knee travel (Z-axis) |
15” |
Quill travel |
5” |
Ram travel |
14.5” |
Spindle motor |
3 HP (1750 rpm @ 60 Hz) |
Spindle speed |
60-500-4200 (2 range, Hi/Low) |
Spindle taper |
R-8 (NMTB-30 optional) |
Quill diameter |
3.375” |
Quill feed rate |
0.0015/0.003/0.006” per rev |
Drilling capacity (manual) |
0.75” diameter |
Drilling capacity (power) |
0.37” diameter |
Boring capacity |
6.0” diameter |
Milling capacity |
2.0 in3/min |
Maximum work load (center) |
750 lbs |
Machine Net weight |
2400 lbs (2500 for 3VSF) |
Shipping Weight/Dimension: |
2500 lbs (2600 for 3VSF) |
*Please note: pricing/specifications subject to change without prior notice. Prices are based FOB our warehouse, CA.
Power requirement: 220/440 volts, 3 Phase, 60 Hz, 10/5 Amp.
3VSF models require 220v, 3 phase, 60 Hz, 10 Amp (optional 440v power requires 5 Amp) but can also accept 220v, 1-phase power (15A) without a phase converter, ideal for customers with only 1-phase power.
.
